How to Adjust a Turnbuckle

Open Body Turnbuckle W/ Swage Stud and Toggle
Open Body Turnbuckle W/ Swage Stud and Toggle

The concept of how to properly adjust a turnbuckle seems to sometimes elude most people. This is understandable as I didn’t used to spend my days thinking about tightening cables, like I do now. So let’s take a moment to discuss how this is done properly.

There are generally three different styles of turnbuckles. Yes, there are a few more styles, however these concepts should give you the gist for any turnbuckle.

Open Body Turnbuckle with a Toggle Jaw at Each End
Open Body Turnbuckle with a Toggle Jaw at Each End

First things first, always make sure that you start by taking out the cotter pins and removing any old tape.

A turnbuckle uses right- and left-hand threads. The direction that shortens the assembly depends on its orientation and which end you are viewing. Hold the terminals correctly and make a small controlled turn, watching whether both ends draw into the body or move outward. Do not rely on a universal “lefty-tighty” rule.

Open-body turnbuckles: Use correctly sized wrenches on the designated flats, holding the stud while turning the body with the specified tool. Do not twist the stay or damage the threads. Identify thread size, handedness, load rating and end fittings before ordering replacement forged-bronze bodies.

Closed-body or tubular turnbuckles: These require the manufacturer’s specified tool and inspection method. A closed-body design does not automatically require replacement; condition, material, thread engagement and suitability for the installation determine that decision. Avoid improvised sharp picks or gripping threaded or polished surfaces with toothed tools.

Double-jawed turnbuckles: Hold the upper terminal with a suitable tool while adjusting the body. Check the installation’s thread orientation rather than assuming every stay tightens in the same visible direction. Do not reverse an assembly simply to match a rule of thumb; follow its installation instructions.

MECHANICAL STUDS AND ROD STUDS : It is also possible that your rigging utilizes a mechanical stud at the top end of the turnbuckle. This is a similar product to that used for open body rod turnbuckles, and the same directions should be followed. Be careful in this situation as the mechanical stud will have two wrench flats, one is to tighten the cap of the mechanical stud (this is NOT the one to use and may cause the fitting to become undone!) and one is to hold the stud in place while turning the turnbuckle body. This wrench flat will sometimes be less noticeable, but if you look closely you will be able to determine which ‘flat’  holds the stud and not the cap.

Mechanical Stud, Similar to Rod Stud
Mechanical Stud, Similar to Rod Stud

TURNBUCKLES THAT UTILIZE RIGGING SCREWS for ROD AND WIRE : Next we have the rigging screw style turnbuckle, which was typically provided by Navtec. This looks like an open body turnbuckle, but in reverse. Instead of one body and two studs, there are two bodies and one stud. This is another typical turnbuckle found on rod rigged boats and you should follow these same guidelines here as well. Again, care must be taken to ensure that the upper end of the turnbuckle does not spin. In this case it is the upper body portion that will need to be either held in place by an adjustable wrench or a spike. Then use another wrench to turn the rigging screw by using the wrench flats on the screw.

Rigging Screw Style Turnbuckle
Rigging Screw Style Turnbuckle

Coquille or stemball turnbuckles: A ball-and-socket deck connection can let the lower terminal rotate as well as the upper one. Hold both terminals at the designated wrench flats while a second person turns the body, using the correct tools. Avoid the improvised vise-grip-and-knee technique: toothed jaws can damage the terminal and make control difficult. See the Hayn stemball-style body for a product example; verify the exact fitting before choosing parts.

Coquille Style Turnbuckle, Popular on Beneteau's and Jeanneau's
Coquille or Threaded Stemball Style Turnbuckle, Popular on, Catamarans with Diamond Stays, Beneteau’s and Jeanneau’s

Maintain the manufacturer’s minimum thread engagement at both ends throughout adjustment, and never adjust a loaded stay without an appropriate rig-support and tuning plan. Stop if threads bind or gall; do not force them. Use only the lubricant specified for the fitting.

When you are done make sure you line up the cotter pin holes in the studs so that the turnbuckle can be pinned. If cotter pins aren’t present then there should be locking nuts of some sort. A turnbuckle ALWAYS needs to be secured so that it cannot become undone.

TIP: No matter what type of turnbuckle you are adjusting make sure the wire, rod or whatever type of stay material you may have, does NOT turn, or is in any way able to become distorted. This can lead to shroud failure!

Remember, if in doubt you can always ask……

Shop replacement cotter pins and Hayn clevis pins. Match the pin diameter, grip length and retaining arrangement to your fitting.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

10 Comments

  1. The top thread on my turnbuckle doesn’t move when I turn….only the bottom one moves. It seems to be fused. Is there any fix for this or does it need replacement?

    1. Hi,

      You can try a torch, propane or MAP gas, either one. Heat it up … A LOT! Then try and turn. If this doesn’t work, soak it in penetrating oil: PB Blaster, AeroKroil, or even WD40. Let that soak overnight and then try one more time. If still nothing, you might be out of luck and need to look at replacing things.

      IF you do get it to turn and notice some metal flakes, bronze or stainless coming out, it will also likely validate replacement.

      Hope that helps.

      ~T.R.C.

  2. For a 32 foot Catalina sailboat. When is the amount of bury an issue. Or asked another way how little adjustment is OK. Thanks,

    1. Hi,
      All the way closed is a problem because that’s all there is, no more tensioning is available. All the way open is only a problem if they cannot be pinned/ secured. You always need enough thread bury to get the cotter pin in at the least. Another way to think of it, or in the case of the closed body, you are looking to have at least enough threads engaged to fill the entire threaded section of the body (top and bottom) to be save.

      ‘Hope that helps.

      ~T.R.C.

  3. very informative article, i have already save it, we will test our turnbuckle with your methods, thanks a lot!