Going Aloft Like the Pros

This may seem a little long winded, but going aloft on a sailboat mast is serious business and should not be taken lightly. Serious injury or death can occur, so please take every precaution. In this article I would like to take a moment to talk about some of the methods that we use to ensure our safety when we go aloft.

The Rigging Company Aloft

Typically, we have to go aloft on boats that we have never seen before. Because of this we have to be very cautious about this process. The first consideration is, that the boat must be in the water, at T.R.C. our company policy is that the boat must be supported in its natural environment (water) to allow for the righting moment of the boat to be effective. We will never go aloft on the hard. The second consideration is, if the boat is too tender, i.e. boats around 27′ or less depending on displacement, you may be better off taking the mast Unstepping small boat mastsdown instead of attempting to go aloft. You should be especially leery about fractionally rigged boats where you need to access the very top of the mast (i.e. J-22), due to the top of the mast lacking support. Also wooden spars can present an inherent safety issue and that is rot, more specifically non-visible rot. When in doubt about an on-the-mast winch like in the case of the wooden mast, it is always recommended to lead the halyard aft to a through-bolted primary jib winch, always ensuring a fair lead.

Once we have determined that the boat itself qualifies to go aloft, we will proceed to inspect the rigging at the deck to ensure all pins are in-place and there is nothing suspicious going on. Ultimately you need to make sure that your mast will not fall over while you are aloft.

"Reel Winch" or Wire Halyard Winch - DON'T USE!!!
“Reel Winch” or Wire Halyard Winch – DON’T USE!!!

Next, we will choose an available halyard that offers the safest possible method to go up the mast. NEVER go aloft on an external halyard that utilizes a hanging block, always choose a halyard that passes through (or into) the mast. Preferably, the halyard should run through a rope clutch before the winch. We will also give the winch a good spin and ensure that the trademark ‘clicking’ sound is present and well pronounced. The click indicates pawl movement, but does not establish that the winch is safe or correctly serviced. We also lift up on the winch drum to ensure that it is securely locked down and will not lift-off during the belaying process. If there is any doubt as to safety of the winch, it is highly recommended to either service the winch, re-lead the halyard to a more suitable winch, or find a more suitable halyard and winch altogether. Also, we never go aloft on a wire halyard or a wire winch. Wire or Reel winches typically don’t have pawls and utilize a metal band (called a Brake) which applies friction to the drum and acts as a brake to keep the drum from spinning the other way. These metal bands have been known to break and down you go!

Since most boats have vertically furling sails of some sort, like in-mast, behind the mast or foresail furlers, the halyard will be occupied most of the year as the working end is attached to the sail at the top of the mast. Sometimes another spare halyard (i.e. boom topping lift or spare jib) is the only option. If nothing else is available it may be necessary to douse one of the furled sails in order to have access to a viable halyard. Unless the halyard looks very new, we will always use a dedicated climbing line. We do this by using the existing halyard to ‘pull-in’ our dedicated climbing line. See your local rigger, or read our blog about methods of attaching the new line to the old one, as there are a number of ways to achieve this.  If we decide to use the existing line, we will run the line to check for any chafe/weak points. We do this by attaching the bitter end to the working end and running the line to the top of the mast and back down to inspect the full length of the line.

After checking the equipment, attach the chair and backup harness exactly as their manufacturers specify. Do not rely on the halyard’s snap shackle. The Harken 2234 instructions specify a figure-eight follow-through through both chair triangles. Have each connection checked before leaving the deck.

Riggers Bosun's Chair

Choose a bosun’s chair or TRC chair with a documented rating suitable for the user, clothing and tools. Never modify a chair or harness to increase its rating. Follow its own instructions for fit, attachment and backup protection. For example, the Harken 2234 is limited to 220 lb (100 kg) total and requires a separate full-body harness on an independent suspension system. A positioning tether does not replace that backup. Read the Harken chair instructions before use.Bosun's Chair Safety Lanyard

Here are some do’s and don’ts to highlight:

  • DON’T use a halyard that is external and utilizes a free hanging block
  • DON’T go aloft on a boat that is on land
  • DON’T use a worn, old, or even remotely suspicious halyard
  • DON’T use a snap or quick release shackle as an attachment
  • DON’T use a line that has a splice of any kind in between you and the winch
  • DON’T use a wire halyard or a reel winch
  • DON’T use a winch that isn’t securely fastened via drilled and tapped machine screws, through bolts, or tight rivets
  • DO tie a safe and secure knot
  • DO make sure that the winch you are using is safe and functional
  • DO make sure that the halyard you have chosen is safe and led properly
  • DO choose a halyard that runs to a rope clutch before the winch, if that is available
  • DO make sure that your chair or harness is equipped with a heavy duty, chafe resistant safety tether and snap hook
  • DO make sure that you are using an adequately rated chair or harness
  • DO use a new halyard (that has been thoroughly inspected) or a dedicated climbing line
  • DO maintain an independently managed backup and follow the tether manufacturer’s attachment instructions

The Climbing Technique: When we go aloft we use a two man ‘heave-ho’ (or ready-go) method. One man in the chair and one man belaying at the winch. Use the number of winch turns required by the equipment instructions, never fewer than the manufacturer specifies and the rope clutch (if present) should be clutched down so as to not let the line slip the other way. This technique takes more coordination than strength. When done correctly this method is the easiest and most effective way to get to the top. The man in the chair finds a good foot hold and hand hold and then says “ready”, pauses, and says “GO!”, with a short pause and then pulls. The short pause after the “GO” is crucial and allows for reaction time by the person belaying on the winch to pull hard at the EXACT same time the person in the chair pulls hard.  The idea is to move the knot up with every “GO”. This method will take practice between the two individuals. Timing is everything!

Climbing aids

The following video illustrates a foothold aid. It does not demonstrate a complete backup system or replace training and the equipment instructions. Do not copy a homemade device for supporting a person without a properly assessed system.

Once you reach your desired height, use the manufacturer-approved positioning attachment and remain on the independent backup. The person belaying you on the winch should put full wraps on the drum, all the while maintaining tension on the line. Do not allow the line to go slack at any time. Then go all the way ’round and through the self-tailer (if present) and cleat the bitter end to a secondary cleat or belay the winch.

Hoisting with a winch

The winch operator must stay focused, maintain clear communication with the person aloft and manage the line throughout the lift. Check the exact winch manual before using it to lift a person. A powered sail-handling winch is not automatically approved for personnel lifting. Keep the independently managed backup in use, stop well before the masthead or any obstruction and never leave a suspended person unattended.

Once you reach your desired height, use the manufacturer-approved positioning attachment and remain on the independent backup and have the person belaying you on the winch go all the way ’round the self tailer and cleat the bitter end to a secondary cleat or belay the winch.

Self-climbing systems

Going Aloft on a self hoistThe rigging company self hoist

Purpose-built systems such as the ATN Mastclimber require training and the complete manufacturer’s procedure. A single ascender is not a complete safety system. Petzl recommends redundant protection. The historical tackle shown here illustrates our shop equipment, not a shopping list for a personnel-hoisting system. Get qualified instruction on compatibility, backup, descent and rescue before using any self-climbing arrangement.

A ratchet block only adds friction; it is not an automatic fall-arrest device. Use the system’s documented method of securing, descending and backing up the climber. A clove hitch used for fenders is not evidence that a personnel-support arrangement is suitable.

How to hoist yourself up the mast

A Note About Mast Pegs, steps, walkers…

…There are also other options to assist while aloft like soft ladders, mast walkers, mast climbing steps, etc… The mounted types involve drilling, screwing, tapping, or riveting dissimilar metals into/onto your mast every 3′ or so along its entire length. Some of the mounted mast steps (walkers) also have a tendency to snag things, trap halyards or rattle (and that’s a lot of things rattling). Soft ladders (like the one pictured here) that are hoisted into the air via halyard, hurt your feet incredibly. Most importantly all of these provide a false sense of security and you should never solely rely on them to go aloft. Make sure that even if your boat is equipped with any of these items that you still use a chair and follow the aforementioned safety guidelines.

The descent

Agree on the lowering signals before starting. Maintain control of the working line and independent backup throughout the descent. Use the winch turns and lowering procedure specified for the equipment, with clear communication between the crew and person aloft.

If the line jams or needs to be pushed off the winch, stop. Secure the person on the independent backup before addressing the jam. Do not experiment with removing turns while relying on that same line for support.

DO NOT let the line run through your hand. Instead lower the Bosun hand over hand, slowly and smoothly. If you encounter a twist in the line, pause and patiently work it out, all the while maintaining tension on the line and focusing on the task at hand (pun). NEVER take your eyes off of the winch and listen clearly for any signals from aloft. If utilizing one of the solo aloft devices follow that manufacturer’s guidelines for descent. If using a self hoist, lower yourself hand over hand slowly. Don’t hesitate to take a few breaks on the way down to make sure you aren’t becoming fatigued. Take time to become comfortable with the sensation.

Jimmie Cockerill The Rigging Company going aloft alone
Self Hoists Make You Sweat! Click the Image to Learn More about the Author.

Shop Harken bosun’s chairs, TRC bosun’s chairs. Read the chair specifications and manufacturer instructions; retain the independent safety arrangement discussed above.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

3 Comments

  1. Good article
    We pull the spare halyard tight beside the mast, then put a Prussik knot on it. This is attached to the bosun’s chair, and is slid up and down by the climber. Thus a totally independent safety
    We like, and use, our folding mast steps, but with or without them the chair is hoisted by a self tailing winch, line through a jamb cleat for ascending and sitting at work.

    Before going up, the climber gets about 4 feet up, halyard is tightened and he jumps off. The shock load is well over his weight, so we are fairly sure the halyard will not break
    We have 12 mm dyneema halyards and Andersen 52 winches, so the safety margin is larger than on smaller boats

    Not all pros are like him. The only pro we have had in ten years cruising was the mast builder’s man who came to help we amateurs install the mast. He simply asked one of us, who he had met first time a coupl of hours previously, to crank him to the top, worked away then back down a few times. I was annoyed at his lack of care, but he refused to change his style

  2. I go aloft by using a mountain climbing handle system similar to ATN (but cheaper). However I always use a second safety line made of a second halyard attached to my harness (no chair). That security halyard is “following” me up (manned by a second person to the winch) or I manned it myself using a Grigri if it is a solo climb. Going down is via the security halyard.

    1. Philippe,

      I'd say this sounds fine. You have a unique situation where all of your halyards hang from blocks externally, right? The only thing I might add is just be sure that you are tying a knot with this security halyard and not using the shackle or the splice to support your body weight.
      

      ~Jimmie