Showing 1–16 of 29 results
Colligo Torque Rope Clamps are designed for use with Code 0, gennaker, and spinnaker furlers that utilize a torsion cable. The clamps are easy to install and can be adjusted as needed. Works with all major furler models, sold per clamp. Note that for some furler systems, two clamps are recommended at one or both…
Selden continuous furling lines are a cover-dependent double braid polyester line. They come factory-spliced into a continuous loop, and have the option of being spliced into a Selden Twin Cam block. Length listed is the length of the loop on deck – e.g. a 4m rope length is an 8m length of rope spliced into…
TECHNICAL FEATURES PBB 50 • Polymer sheave. • Stainless steel strap for strength and long service life. • Torsional rigid cheeks in glass fibre reinforced polymer to prevent jamming. • Sliding swivel locking mechanism.
The Selden double stanchion fairlead for continuous furling lines are designed to slide over 25-30mm (1 to 1-1/4″) stanchions and feature a spring-loaded metal bracket that can be opened to capture a continuous furling line without having to undo the splice in the line.
The Selden dead-end fitting is installed in the mast to serve as a termination strongpoint for 2:1 halyards. The fitting requires a cutout in the mast and is held in place with four fasteners that thread into the integrated backing plate.
In order to achieve the desired performance of a top-down furling system when using a Code 0 or asymmetric spinnaker, the halyard load must be higher than what normal halyard boxes and stoppers can handle. Therefore, a 2:1 purchase is recommended to be used. The halyard is dead-ended at the mast (preferably with a swivel…
Colligo Terminator end fittings are the only spliceable, lashable, and pinnable end fittings available that meet Hampidjan’s recommended minimum 5/1 bending ratio for Dyneema. This is essential for long term durability of Dyneema-based lines, as tight bending radii can cause compressive stresses that weaken the line considerably. Clevis pin holes come with a bushing installed,…
Harken® recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. The 7403 outboard assembly allows furling line to travel outboard of the stanchion to keep the sidedeck clear. Block mounts with a strong four-screw clamp without removing the stanchion or lifelines. Sheave dia: 1-1/8″ – 29mm Max line: 3/8″ –…
Harken® recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. Use the 7405 as an inboard lead for two lines, useful for continuous line furlers or cutter rigged boats with two furlers. Sheave dia: 1-9/16″ – 40mm Max line: 3/8″ – 10mm Max working load: 485lb – 220kg For use…
Harken® recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. Use the 7401 40 mm block on the bow pulpit as an inboard lead. Both the 7401 and 7402 have ball and socket bases to align blocks for smooth leads aft. Sheave dia: 1-9/16″ – 40mm Max line: 3/8″ –…
Harken® recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. A 7402 ratchet maintains tension when spooling so the unit can furl smoothly and easily. Both the 7401 and 7402 have ball and socket bases to align blocks for smooth leads aft. Sheave dia: 2-1/4″ – 57mm Max line: 3/8″…
Harken recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. Use the 7401 or 7407 block on the bow pulpit as an inboard lead. 7401, 7402, 7405, and 7407 have ball-and-socket bases to align blocks for smooth leads aft. Sheave dia: 2-1/4″ – 57mm Max line: 3/8″ – 10mm Max…
Harken® toggle assembly accepts standard turnbuckle using swage, rod, Norseman®, or Sta-Lok® terminals. Toggle flips for fork or tang chainplate installation. A single stainless steel clevis pin provides access to the turnbuckle for adjustment. These toggles are made to work with a particular furler model – be sure to select the correct furler unit as…
Halyard restrainers prevent the halyard from wrapping around the foil on boats where the swivel isn’t mounted near the masthead. Small: Sheave dia: 15/16″ – 25mm Fasteners: #10 RH in – 5 RH mm For Harken furling unit: 0, 1, 1.5 Large: Sheave dia: 1-1/4″ – 31mm Fasteners: #10 RH in – 5 RH mm…
Harken clevis pin swivel snap shackles can be pinned onto a furling drum or top swivel for sail tack or head attachment, respectively. Snap shackle facilitates quick sail changes.
Harken® toggle assembly accepts standard turnbuckle using swage, rod, Norseman®, or Sta-Lok® terminals. A single stainless steel clevis pin provides access to the turnbuckle for adjustment. These toggles are made to work with a particular furler model – be sure to select the correct furler unit as well as the correct pin size. These toggles…
No products in the cart.
This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
